- Replace vinyl on main bulkhead with teak
- Replace teak surround on forepeak hatch
- Fit hydrovane wind vane steering
- Fit life raft
- Fit clutch to mast for main halyard
- Fit third reefing point on boom
- Make and replace direct current switch panel
- Make up new warps and anchor snuber
- Fit new steering compass and wire up light
- Fit Hampshire Heater
- Fit tiller pilot to wind vane steering
- Cover wheel with leather
- Fit new auto helm controller
- Wash out and clean water tank
- Paint cockpit lockers
- Replace masthead tricolour and anchor light
- Replace masthead windex
- Service engine
- Replace all fuel hoses to engine
- Replace through hull fittings, heads inlet and outlet, bilge and old heater exhaust
- Replace all hoses to and from heads tap
- Replace shower / tap in heads
- Paint heads lockers
- Fit water filter to galley cold water supply
- Fit new primary fuel filter
- Replace water filler hose and repaint cupboard
- Derust and repaint engine
- Fit over engine light
- Replace fule hoses from fuel tanks to engine and returns
- Repack rudder stock packing and clean and restore collar fitting
- Replace and refit cutlass bearing
- Reseat cutlass bearing carrier. Work completed by Joe Pycroft
- Fit new fire proof and sound insulation to engine compartment
- Paint engine compartment
- Fit new battery isolation switch with VSR to automate charging
- Fit new grounding wires to anode
- Fit higher rated positive and negative cable from battery to buss bars
- Fit heavy duty fuse in live side cable
- Replace all cables to and from new battery isolator
- Fit new positive and negative buss bars and re-wire to DC distribution panel
- Fit new stern gear box seal - carried out by Cutler Marine
- Repair teak deck
- Polish hull, deck and coach roof
- Touch up copper coat where required
- Service engine
- Bend on sails
- Re-wire raw water calorifier pump
- Fit new hoses from engine to calorifier
- Fix light in main cupboard
- Replace galley sink plug chain
- Fix LED light over galley
2013
- Service engine - October 2013
- Clean and descale raw water supply to engine
- Replace rubber cuffs to oil cooler
- Replace engine heat sensor
- Replace thremostat
- Replace impeller
- Service engine - Janaury 2013
- Fit Raymarine remote control - Janaury 2013
- Fit NASA navtext - Janaury 2013
- Build new gas locker and lid - January 2013
- Service cobra steering - Janaury 2013
- Build internal rack for GPS, Navtext and VHF aerials - Janaury 2013
- Fit aerials to rack and rewire to through boat - Janaury 2013
2012
- Replace Lavac toilet with Jabsco toilet and build new support - October 2012
- Refit cockpit safety line U bolts with backing plates - April 2012
- Replace drive belt to wheel steering autohelm - April 2012
- Wash, top and tail and refit all standing rigging - April 2012
- Fit securing lines to washboards and cleat - April 2012
- Build storage for wash boards in main cardrobe
- Buy and fit new mainsheet track - April 2012
- Sand blast hull to remove antifouling an sand down hull ready for epoxy coat
- Construct and fit washboard storage frame in large hanging locker - April 2012
- Cockpit cover and spray hood cleaned and sealed by C&J Chichester - March 2012
- Mercury 2.2hp outboard serviced by Home Marine - March 2012
- Remove foam covering from two bulkheads and face off - March 2012
- Fit teak veneer to forecabin door suround and other areas - March 2012
- Clean and re-paint forecabin low level lockers - February 2012
- Engine, gear box oil change and filter replacement - January 2011
- Fit AIS transponder and connect to laptop
- Replace main sail with fully batterned sail from Sanders of Lymington
- Liftout, antifoul polish and replace anode
- Replace propeller shaft seal with PSS type
- Buy new shaft seal
- Purchase and fit replacement yankee
- Service engine and replace filters
- Liftout, antifoul polish and replace anode
- Replace domestic radio with new Sony version
- Seal cockpit locker tops with glass resin
- Replace 2 portlights above galley with opening hatchs
- Write up and laminate safety briefing notes
- Clean and service heads Henderson pump
- Clean and repaint heads lockers and insulate
- Clean and repaint saloon lockers and insulate
- Clean and repaint forepeak lockers and insulate
- Clean and repaint hanging cupboard and insulate
- Clean, polish and service hatches and surrounds
- Refit panama fairlead to port bow
- Fit new stay sail from Quay Sails of Poole, June 2009
- Replace teak pellets on deck and toe rail
- Fit emergency climbing safety ladder to pushpit
- Instal separate power supply for TV booster
- Replace jubilee large clip on exhaust muffler
- Refill rudder grease rudder pot
- Change screws on impeller face plate for quick reelease wing nuts
- Antifouled, polish topsides and replace anode
- Replace cutlass bearing
- Mend teak toe rail
- Replace missing teak pellets
- Fit carpet to salon area
- Fit electric bilge pump
- Service outboard
- Rub down rust spots on engine, treat rust areas, clean down engine bay and touch up paint
- Polish coach roof, side decks and outside of cockpit
- Prepare / Sand down companionway area and washboards
- Teak / Danish all internal teak
- Clean and polish stantchions
- Re-fit dan-buoy stand
- Fit overflow pipe to engine siphon hose and run back into bilge
- Buy and fit new automatic fire extinquisher to engine compartment
- Seal off old pipe work to heater
- Remove old diesel heater
- Fit front retaining bar to bookcase
- Replace original chain plate backing plates with new enlarged stainless steel plates.
- Fit L bracket to aft lowers to improve strength
- Mend yankee and main sails
- Mast stepped and all electrical wires replaced
- Buy and fit new Lopo tri coilour and anchore light to mast head
- Prepalce steaming and deck light fitting
- Tape up and use seizing wire where required on boom, mast, rigging and stanchions
- Calibrate log and wind instrument
- Fit ensign to backstay
- Check all mast fittings, clean and lubricate sheaves
- Remove all U bolts and backing plates
- Fit to VHF new bracket with sikaflex
- Run VHF cable down mast
- Fit TV bracket
- Fit TV bracket with sikaflex
- Fit new wind instrument to tope of mast with sikaflex under
- Fit Raymarine wind instrument to top of mast and re-wire
- Fit new VHF aerial to top of mast and re-wire
- Fit TV aerial to top of mast and re-wire
- Fit new spinnaker block to mast head U bolt
- Fit galvanic isolator
- Service engine and gearbox replace filters
- Purchase and fit new Spray hood from C&J Chichester
- Purchase and fit new cockpit cover for C&J Chichester
- Purchase Flat screen TV
- Fit new stainless steel dual anchor roller bow roller
- Fit stainless plate to bulkhead by cooker
- Fit Blue Sea AC 240volt, 16amp, four 8amp breaker power distribution panel
- Purchase Blue Sea AC 240volt, 16amp, four 8amp breaker power distribution panel
- Remove and replace engine thermostat and seals
- Remove engine water pump and service
- Purchase galvanic isolator
- Water pump serviced and seals replaced
- Fit teak mobile phone holder behind navigation seat
- Purchase and fit Webaco 25amp 12 volt charger
- Refit depth, speed, wind and auto helm displays in cockpit
- Remove and check propeller and re-fit
- Fit new Raymarine VHF radio
- Fit new speed, depth transducers and instruments
- Purchase Raymarine speed, depth and wind instruments
- Remove remaining Stowe instruments and wiring
- Make up rope tidy in portside locker
- Strengthen sides of cockpit lockers and make base for rope tidy
- Replace fridge with new 55 version and cold plate
- Remove old fridge components
- Purchase replacement fridge components
- Connect graphic display
- Move Autohelm display / control head from locker to bulkhead
- Remove stowe wind angle display and log display
- Purchase Graphic display
- Upgrade SeaPro to 3000
- Connected Raystar 125 GPS to Smart Pilot
- Purchase Raystar125 GPS
- Change gear box and engine oil and oil filter
- Re-seat all stanchion posts
- Replace split pins at base with nut and bolt
- Purchase and fit outboard cover
- Replace more teak pellets
- Re-seat starboard push-pit stanchion
- Rewire bow light
- Purchase new bow light
- Clean teak deck
- Fit drogue to life buoy
- Remove anchor fittings on teak deck and place anchore on bow roller
- Glue down loose teak plank
- Replace teak pellets on deck
- Polish cockpit
- Connect up wiring to autohelm
- Connect up power to autohelm
- Fit Rudder angle indicator
- Fit control head
- Fit smart pilot
- Fit autohelm gyro compass / fluxgate compass
- Fit S1 autohelm motor to wheel
- Purchase Raymarine S1 wheel pilot £699.95 (July 2007)
- Polish remainder of deck level fibreglass
- Remove old Streamline GPS system and wiring
- Grease nipple on upper rudder stock
- Grease emergency tiller through cockpit floor fitting
- Insert extra car lighter socket for inverter in navigation station
- Replace both domestic batteries 110amp (June 2007)
- Polish stainless steal work
- Polish hull above rubbing strake
- Re-route to heads sink
- Replace hoses where not already replaced, heads, sinck etc.
- Clean fenders
- Clean and polish topsides, anti foul, paint boot top
- Replace anode and bolts
- Replace heads sea cock in
- Replace heads sea cock out
- Fibreglass existing holes
- Remove existing though hull fittings for heads
- Clean propeller
- Fit pump guard to shower / sink outlet
- Fit non return valve to shower tray / sink
- Fit sink / shower tray electrical pump and in-line filter
- Purchase sink / shower tray electrical pump
- Replace heads sink / shower through hull fitting and sea cock
- Repaint main hanging locker and shelves
- Re-bed two stanchions with M6 x 30mm pan head screws
- Fit torch in galley next to fire blanket
- Reseal water filler on deck and re-bed
- Replace self amalgamating tape around diesel fuel sight gauges’
- Top up batteries
- Fit safety retention strap around batteries
- Buy 2 lengths of green 10mm x 15m Marlow double braid
- Buy second 60mm Lewmar block
- Buy 2 lengths of Marlow braid 10mm x 4 for preventer on boom
- Fit eyes to front of boom
- Fit shackles to boom preventers
- Tie preventers to aft end of boom
- Fit Spinlock blocks to stanchions
- Run preventer / downhaul lines
- Fit preventer Lewmar block to foredeck “U” bolt
- Fit “U” bolt to foredeck
- Varnish step on top of engine
- Teak oil all teak
- Paint teak deck with Polycell 3 in 1 mould remover
- Fit fire extinguisher in engine compartment
- Clean internal brass work
- Fit new lid to battery compartment
- Replace negative engine / battery cable
- Paint bilge under old battery box
- Remove old battery box and clean bilge under
- Clean bilge under engine
- Thoroughly clean engine and WD40
- Buy engine fire extinguisher
- Fit emergency tiller in bottom of port cockpit locker
- Label first aid kit, dressings, drugs, ointments
- Label spars boxes
- Service engine, change oil, change oil filter, check impeller and engine anode
- Clean impeller front and replace brass screws
- Replace primary and secondary fuel filters
- Replace salt water gusher pump mark 3
- Remove salt water gusher pump mark 2 for servicing
2006
- Label ropes at mast
- Move radio and re-connect
- Fit lighter plug to Aldis lamp
- Buy containers for Handheld VHF, Aldis lamps and head lamp
- Replace VHF cable through deck fitting
- Rewire coaxial VHF radio cable from mast to radio
- Fit new shackle to staysail halyard
- Make and fit new lid to battery locker
- Enlarge battery locker lid
- Write boat name on life jackets and safety lines
- Stick reflective tape on life ring and danbuoy
- Purchase lead line
- Purchase safety lines (jack stays)
- Purchase ocean safety life jacked - Automatic 150 newtons
- Purchase Icom M31 mobile VHF radio
- Fit backing pads to underside of deck in navigation station to support radar and VHF
- Free up and re-fit cover over rudder stock
- Fit and wire up 240V socket at navigation table.
- Fit 240v sockets in main cabin
- Buy and fit new hot raw water pump in hot water domestic system
- Service all 8 winches (August 2006)
- Fit torches to fore cabin and heads
- Paint emergency tiller
- Fit flare container under Navigation table
- Mend / replace heads sink switch
- Buy water proof aldiss lamp
- Fit bungee to keep swing doors open
- Fit drogue to life buoy
- Buy and fit two pin point white flares to underside of perch
- Replace 1 fender and add additional fender
- Fit 240v socket to port locker in salon and in forepeak
- Buy anchor light
- Paint coach roof
- Fit knife in cockpit
- Buy diesel Gerry can
- Fit “U” bolt beneath staysail inner forestay for halyard connection
- Put seizing wire on jack stay line shackles
- Buy larger softwood cones and tie to sea cocks plus stow spares
- Fit eye bolts at bow for safety lines
- Fit light and whistle to life buoy
- Name on life buoy
- Fit jack stays (safety lines)
- Fit teak divides to cooking implement draw
- Fit rope tidy in anchor locker
- Fit teak rail in anchor chain locker for rope store
- Fit roller furling line blocks to stanchions
- Replace main sheet
- Replace yankee sheets
- Service boom and vang
- Replace reefing pennants
- Replace main outhaul
- Replace pole up haul
- Replace spinnaker halyard
- Replace pan head screws to impeller cover
- Fit new engine impeller
- Replace bolts on shaft coupling
- Purchase two life jackets
- Rub down hull and touch up epoxy
- Replace electrical bonding to rudder, binnacle and engine
- Repaint anchor locker and forward locker
- Clean rudder fittings and repaint rudder fittings
- Repaint rudder compartment under cockpit sole
- Replace pinch bolt on rudder stock with stainless steel bolt
- Replace engine saltwater supply hose
- Replace anti siphon hoses to exhaust
- Replace seals in forward shaft bearing
- Replace cutlass bearing, shaft diameter 30mm, external 1.75”, length 120mm)
- Replace cockpit sea cocks
- Replace engine raw water in sea cock
- Fit water strainer to raw water intake
- Replace saltwater inlet sea cock
- Replace all standing rigging including upgrade bobstay and SSB insulators
- Replace headsail Rotorstay furler reefing with Profurl Classic LCI 42
- Replace all major hoses to and from engine
- Replace staysail halyard
- Replace headsail halyard
- Replace tap in galley for new mixer tap
- Connect up salt water supply to old tap
- Top up fuel tanks and add bactericide additive
- Wash ropes and lines
- Change 240v inlet
- Drain all pipes, pumps, water tanks and calorifier
- Winterise engine
- Purchase spares
- Engine oil 4.9L 15/40 multi grade
- Gear box oil 1.1L
- Drive belt
- Oil filter
- Primary fuel filter
- Secondary fuel filter
- Impeller and gasket
- Service Bukh DV36ME engine
- Remove and replace thermostat and seals
- Drain down calorifier
- Drain out all salt water and flush with freshwater and anti freeze
- Top up batteries and Vaseline connections
- Wash out engine room and bilge
- Check and replace engine anode
- Check polarity of extension lead and 240v wiring
- Fit 240v 2 gang socket in galley and rewire companion way socket
- Buy and replace exhaust hose downstream from muffler 1.6M long
- Fit shore power 3 pin socket in lazerette
- Mend aft navigation light and rewire back to DC breaker board
- Buy and fit staysail sheets
- Fit 3rd “U” bolt for safety harness at aft of cockpit
- Buy baseline U bolt for aft deck life line
- Fit hatch spring on drinks cabinet
- Fit hatch spring on glasses cabinet
- Free up spinnaker pole
- Purchase and replace first aid kit
- Replaced main halyard
- Replaced topping lift
- Replaced staysail furling line
- Replaced yankee furling line
- Replaced fender lines
- Replaced Vang
- Fit new galley fire extinguisher
- Fit fire blanket
- Service cockpit primary winches
- Fit spare 2 x U bolts in cockpit
- Fit bungee in lockers to hold up locker lids on winches
- Fit hatch spring to navigation table lid
